Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterDoorKing Gate Installation in Arlington: What to Know First
We install, service, and repair DoorKing gate operators and gate systems throughout Arlington, TX, and we do it as an independent DoorKing service provider. Most DoorKing gate installations take one to two days once parts are in, and you’ll get the price before we touch a tool. We’ve been at this since 2001, and the quote you sign is the price you pay. Call (817) 241-4067 for a free estimate.
If you own a DoorKing unit and the gate won’t open, cycles halfway, or groans like it’s tired of living, this page tells you exactly what’s likely wrong, what it costs to fix in Arlington, and why we handle DoorKing jobs differently than the franchise outfits that swap parts until something works. Hal Gatewood’s name is on the shop, and the shop is down the road. That’s the oldest accountability there is.
Key takeaways:
- We install, service, and weld for DoorKing swing, slide, and barrier gates across Arlington and surrounding areas.
- Repair-first mindset: we fix what’s broken, not what’s adjacent to the break.
- Upfront pricing, no trip charge inside the county, and a 90-Day Done Right Promise in writing.
- A live person answers the phone at (817) 241-4067, day or night.
How DoorKing Products Fail - and How We Fix Them
DoorKing builds solid American-made operators. But twenty-plus years of working on them around Arlington teaches you where each series likes to fail, and what actually fixes it. Here’s what we see most often:
- DoorKing 9150 slide gate operator failures from low-voltage wiring loads. The 9150 is a workhorse, but it pulls more current than people expect, especially on heavier gates. We regularly find callers dealing with a dead board because the original install used wire too thin for the run. We re-pull proper gauge, test the draw, and save the board from cooking itself twice.
- DoorKing 6002 swing gate hinge wear causing operator overload. I’ll say the same thing on a driveway that I’d say at the shop: a gate sags in the hinge post, not in the middle. When a 6002 won’t hold its limit settings, it’s almost never the operator. It’s worn hinge bearings or a post that’s drifted. We fix the post, rebuild or replace the hinge, and the operator stops fighting itself.
- DoorKing 9050 “ghost reversal” from Arlington’s clay soil shifts. North Texas clay breathes with the seasons. Wet winters swell it, dry summers shrink it, and a concrete pad that was level in March can be off enough by August to make the 9050’s reversing edge trip when the gate’s two inches out of plumb. We re-level the operator, shim the track, and run the full obstruction test so it stays honest.
- DoorKing barrier gate (1602 series) arm drift after collision damage. If someone backed into the arm at the parking lot gate, the spring tension’s thrown off and the motor may have a cracked gear as a souvenir. We don’t just re-tension and walk away; we inspect the gear teeth and the arm mount for hairline cracks. Found one on a 1602 off Cooper Street last fall that two other companies had “fixed” by tightening the same stripped bolt.
- DoorKing DKS 9300 vehicular slide gate limit switch corrosion. These limit switches sit near the ground and don’t survive Arlington’s humidity plus asphalt runoff. When the gate stops a foot short or over-travels into the post, that’s usually the culprit. We replace with sealed limit assemblies and re-set the stops. We don’t silicone-spray the old ones and call it a day.
We service the whole DoorKing line: the 9150, 9050, 6002, 6050, 1602 barrier operators, the DKS 9300, and the access control keypads that come with them. Each one has habits. Knowing a model’s habits is what separates a repair that lasts from one that doesn’t.
Our DoorKing Gate Installation Process
Here’s how a DoorKing gate installation goes when you call Gatewood Fence & Gate:
- 1
You call (817) 241-4067. A person answers. No phone tree. Hal picks up or one of his crew does. We ask what the gate’s doing, what operator you have, and what time works for you.
- 2
We come out and look - really look. Before we ever touch a bracket, we check the post, the hinges, the gate’s weight and alignment, the existing opener, and the power situation. On a DoorKing slide gate, we check the track condition and wheel bearings. On a swing gate, we check where the post is actually planted.
- 3
We give you a written price. The quote covers the work and the parts. If we can fix rather than replace, we say so, even when the replacement would’ve cost more. Fix the panel without the post and you’ll fix it twice. We’d rather tell you that up front than sell you two jobs.
- 4
We do the work in your driveway. Hal welds on-site. The gate doesn’t get hauled off to some shop across town. When we need parts - an OEM DoorKing board, a gear set, a limit switch - we order what’s right for the model year, and we’re clear about whether it’s OEM or a solid aftermarket equivalent. Some aftermarket boards are genuinely good. Some aren’t worth the box they ship in. We don’t install the bad ones.
- 5
We test, then test again. The gate cycles under load, the reversing feature gets verified, the limits get set with a tape measure not a guess, and the close timer gets set for your driveway, not somebody else’s.
- 6
You get the 90-Day Done Right Promise. In writing. If something’s off, one call brings us back. No runaround.
What DoorKing Gate Installation Costs in Arlington
Here’s what DoorKing gate work actually runs in Arlington and the surrounding area. These are real numbers from jobs we’ve done, not prices Xeroxed off a national price sheet:
- DoorKing 9150 slide operator install (new unit): $2,800 - $4,600 depending on gate weight, track work, and wiring run
- DoorKing 6002 swing operator install (single gate): $1,900 - $3,200
- DoorKing 6002/6050 swing operator install (double gate, both sides): $3,500 - $5,800
- DoorKing board replacement (9150 or 9050): $450 - $850 installed
- DoorKing limit switch replacement (9300 series): $180 - $320 installed
- DoorKing gear/chain replacement on slide operators: $400 - $900 depending on the series and the damage
- Full-site service call with diagnosis: No trip charge inside the county. If it’s a repair, you’ll hear the price before we start.
What moves the price: the weight of your gate, the wire run from the panel, the condition of the posts, and whether the existing operator was installed with enough clearance to begin with. We’ve seen DoorKing units squeezed against fence lines that needed move-and-reset work before the operator could ever cycle right. The written quote covers all of it before work begins. Call (817) 241-4067 for an exact number on your gate. Estimates are free.
Why Arlington Homeowners Call Gatewood Fence & Gate for DoorKing Work
The name on the shop is Gatewood, and the person who answers the phone is the person who owns the place. Hal’s been fixing gates around Arlington since 2001, back when he was driving a truck with a busted AC and figuring things out one broken hinge at a time. He took welding and metal fabrication at Tarrant County College before he ever touched a gate opener for a paying customer, and he grew up near Pantego on the southwest side of Arlington. That’s not a corporate bio. It’s just where we’re from.
Every DoorKing job carries the 90-Day Done Right Promise, in writing. If it’s not done right, we make it right. One call brings us back. No fine print, no fighting over who’s at fault. We also service LiftMaster, Mighty Mule, and Ghost Controls, so if your property’s running a mixed setup, you don’t need two phone numbers. We keep it honest. We don’t swap good parts to inflate a ticket. If we find a $2 bolt behind a $400 failure, we’ll tell you.
DoorKing Gate Installation FAQs
Yes. We install and service DoorKing equipment no matter where you bought it, as an independent DoorKing service provider. You don’t need a dealer relationship to get a gate that works. We quote the install, do the install, and stand behind it with the 90-Day Done Right Promise. Call (817) 241-4067 and we’ll come look.
DoorKing’s warranty covers manufacturing defects on the unit itself, and a professional independent install doesn’t void it. What we avoid at all costs is sloppy wiring or mounting that causes damage the warranty wouldn’t cover anyway. We’ve taken over plenty of jobs where bad installs cooked control boards, and boards killed by bad wiring are never covered. We do the install right the first time so neither you nor DoorKing has anything to argue about. And if we touch it, the 90-Day Done Right Promise applies regardless.
Most common DoorKing parts are available quickly, sometimes same day if the local supplier has them in stock. Boards, limit switches, gear sets, and remotes are what we keep common replacements for. For unusual series or older models, we may need a day or two to have parts in hand. The 24/7 live phone at (817) 241-4067 means you can tell us what failed on a Saturday night and have a real plan by Sunday morning.
If the motor’s not seized, the board’s not fried, and the gears aren’t stripped, repair usually makes more sense. A well-maintained DoorKing 9150 can run for twenty-plus years. When the cost to repair climbs past roughly sixty percent of a new unit, we’ll tell you that too, and we won’t be cagey about the math. Show me the gate closing on its own and I’ll show you where it’s failing. We figure out which side of that line you’re on before recommending anything.
In most cases, yes. We run installation and service calls across Arlington and the surrounding area every weekday, and we’ll tell you honestly when the next window is. Same day depends on our route and your side of town, but the phone’s answered 24/7, so you’ll always reach a human. Just give me a call - I’ll pick up. (817) 241-4067.
Contact Gatewood Fence & Gate for DoorKing Gate Installation in Arlington
If you’re in Arlington, Pantego, Dalworthington Gardens, Kennedale, or anywhere else in Tarrant County with a DoorKing gate that needs a proper install, call (817) 241-4067. We’ll give you a straight price, do the work in your driveway, and stand behind it in writing. Free estimates. No trip charge inside the county. $40 off any repair over $200, and a permanent 10% discount for seniors and veterans. The name’s on the shop. Call and see who answers.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Arlington and nearby areas.