Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterDoorKing Gate Repair in Arlington: What to Know First
DoorKing gate repair in Arlington typically runs $185 to $650 depending on whether the problem is the control board, the actuator arm, or the gate hardware itself, and most jobs are completed same-day or next-day once we diagnose the unit. We’re an independent DoorKing service provider, not a factory warranty center, which means we’ll tell you straight whether OEM or quality aftermarket parts make sense for your gate rather than defaulting to whatever the distributor pushes. If your DoorKing opener is clicking but not moving, or the gate stops halfway and reverses, that’s an electrical or limit-switch issue we can usually pin down within the first 30 minutes on site.
This page is for Arlington homeowners with a DoorKing swing or slide gate that quit working, got slow, started slamming, or simply won’t stay closed. You’ll find honest pricing, the specific ways these units fail around here, and the repair process we follow. Call (817) 241-4067 and you’ll get a live person, not a recording.
How DoorKing Products Fail - and How We Fix Them
DoorKing builds a solid opener, but every line has its known weak points. Here’s what we actually see on Arlington properties, not what a parts catalog tells you to look for:
- DoorKing 6002 and 6003 swing gate arms: The internal limit switches wear out from years of sun and heat cycling against the actuator housing. The gate opens fine but then creeps or slams at the end of travel. We replace the limit assembly and re-set the travel, rather than selling you a whole new arm.
- DoorKing 9000 series slide gate operators: The drive chain stretches and the tensioner gets ignored until the chain jumps the sprocket. That’s the one where the gate jerks forward a few inches and stops. We re-tension or replace the chain and sprocket together, because putting a new chain on a worn sprocket buys you about six months.
- DoorKing control boards after a power surge: Arlington summer storms knock out the relay that drives the motor. The board shows a solid red light but won’t respond to the remote or the keypad. We test the board in place before condemning it – about a third of the boards people were told to replace just need the relay soldered, which is a $90 repair instead of a $600 swap.
- Photo eye misalignment on DoorKing slide systems: The gate reverses immediately or won’t close at all. Nine times out of ten it’s a photo eye knocked out of alignment by a mower or a gust, not a bad sensor. We realign, clean the lenses, and verify the beam before touching anything else.
- Hinge post rot on DoorKing swing gate systems: The opener works fine but the gate drags or won’t fully close. The problem isn’t the motor – it’s the hinge post pulling out of the concrete because the original install used wedge anchors instead of through-bolts. We weld a new base plate and re-anchor the post properly. Fix the panel without the post and you’ll fix it twice.
Our DoorKing Gate Repair Process
When you call us about a DoorKing gate, here’s exactly what happens:
- 1
You call and a person answers. Not a robot, not a queue. You describe the symptom, and we give you a straight answer about whether it sounds electrical or mechanical before we ever schedule.
- 2
We show up in the window we promised. Hal or one of his crew arrives with the common DoorKing parts on the truck – limit switches, photo eyes, capacitors, relays – so we’re not driving across town for parts on most calls.
- 3
We diagnose before we quote. We don’t quote over the phone and then “discover” more problems at the door. We put hands on the opener, find the actual failure, and tell you the price before any work starts. That price doesn’t change unless you ask us to do something additional.
- 4
We make a parts call you can see. For DoorKing boards and arms, OEM is the right call when the unit is under factory warranty or less than five years old. For older units, a quality aftermarket board or arm often makes more financial sense. We’ll show you both prices and let you decide. We don’t mark up parts 300% and call it standard practice.
- 5
We repair on site and test it like we own it. We run the gate through 20 full open-close cycles, check the safety reversal, and adjust the force settings so the gate won’t pin a kid or a dog. Then we run it one more time while you watch.
- 6
You get the 90-Day Done Right Promise in writing. If the same problem comes back within 90 days, we fix it free. That’s not buried in fine print – it’s stamped on the invoice.
What DoorKing Gate Repair Costs in Arlington
Here’s what we charge for the DoorKing repairs we do most often in Arlington. These are real numbers, not a teaser price meant to get us in the door:
| Repair | Typical Price Range |
|---|---|
| Photo eye realignment or cleaning | $85 – $140 |
| Limit switch replacement (single actuator arm) | $185 – $260 |
| Control board relay repair | $90 – $150 |
| Control board replacement (OEM DoorKing) | $450 – $650 |
| Drive chain and sprocket replacement | $300 – $480 |
| Hinge post re-anchor and weld | $350 – $700 |
| Full actuator arm replacement (aftermarket) | $400 – $550 |
What moves the price is parts – OEM DoorKing boards and arms cost more than aftermarket equivalents – and whether we’re welding on site or just swapping a component. You’ll never get a “maybe it’s this, maybe it’s that” quote from us. We tell you the cost before we turn a wrench, and the estimate is free. Call (817) 241-4067 and we’ll give you an honest number over the phone.
Why Arlington Homeowners Call Gatewood Fence & Gate for DoorKing Work
We’ve been fixing gates in Arlington since 2001, back when Hal Gatewood was still driving a truck with a busted AC and figuring things out one broken hinge at a time. Hal grew up near Pantego, took his welding and fabrication courses at Tarrant County College, and the Gatewood name has been on the shop door ever since. You won’t talk to a call center. You’ll talk to Hal or someone who works directly for him, and if you want to look somebody in the eye before you hire them, the shop address is published and the door’s open.
We carry parts for all nine major gate brands – DoorKing, LiftMaster, Mighty Mule, Ghost Controls, FAAC, BFT, Linear, Viking, and Elite. That matters because when a DoorKing control board fails and it’s a three-week factory order, we can often cross-reference a compatible board from another brand and get your gate running the same week. And every single job, DoorKing or otherwise, carries the 90-Day Done Right Promise in writing. One call brings us back, no runaround.
Frequently Asked Questions
In most cases yes – if you call before noon on a weekday, we can typically have someone at your Gatewood repair job the same day or the following morning. We keep common DoorKing parts on the truck, which means the first visit usually fixes the problem rather than just diagnosing it. Call (817) 241-4067 in the morning and we’ll give you a straight answer about timing.
No, we’re an independent DoorKing service provider, not a factory-authorized dealer or warranty center. For homeowners, that usually works in your favor: we can use quality aftermarket parts when OEM isn’t the smart money, and we don’t have a distributor quota pushing us to sell new openers when a repair makes more sense.
If your opener is still under the factory warranty, we’ll use OEM DoorKing parts and follow their documented service procedures, which keeps your warranty intact. If the unit is out of warranty – which is most of what we see in Arlington – we’ll give you the straight comparison between OEM and aftermarket and let you decide.
As a rule, if the gate frame, hinge posts, and mounting are solid, the opener itself is almost always worth repairing. We’ll tell you plainly if we think a repair is a band-aid – we’d rather lose a small job than sell you something that fails again in eight months. A new DoorKing opener runs $1,800 to $3,500 installed, so a $300 repair usually wins the math.
The DoorKing 6002 and 6003 swing gate actuators are everywhere in Arlington’s older neighborhoods, while the 9000-series slide operators show up on gated driveways in the county. We know both lines cold – their limit-switch wear, their chain-stretch failures, and their post-anchor issues – so we’re not learning on your gate.
No trip charge inside the county, and estimates are free. If we show up and you’re not there, that’s on us – we don’t bill you for our scheduling mistake. The price we quote is the price you pay, and that’s the way it’s been since 2001.
Call Gatewood Fence & Gate for DoorKing Repair in Arlington
If your DoorKing gate is acting up – clicking, reversing, slamming, or just plain dead – call (817) 241-4067. You’ll get a live person who can tell you over the phone whether it sounds like a board problem or a mechanical issue, and we’ll schedule a time that actually works. Free estimates, upfront pricing, and a written 90-Day Done Right Promise on every job. Just give me a call – I’ll pick up.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Arlington and nearby areas.