FAAC Hinge & Roller Replacement Nationwide | Gatewood Fence & Gate

FAAC Hinge & Roller Replacement: The Arlington Owner’s Guide

We stock and install FAAC-compatible hinge and roller replacement parts for swing and slide gates throughout Arlington, and most swaps run $140 to $320 installed depending on the model and condition of the gate. We keep the common wear items on the truck, so a lot of these jobs happen same-day. You’ll know a hinge or roller is going when the gate starts dragging, leaning, or making a groan that wasn’t there last spring. In Arlington’s heat and our occasional ice storms, the nylon rollers and pivot bushings are usually the first things to wear out long before the motor or control board gives you trouble.

Call (817) 241-4067

The catch with FAAC gates is that the hinge geometry and roller diameter are a little different than what you’ll find on a big-box store replacement. Fit the wrong one and the gate binds, the motor strains, and you’ll be back under there in six months. We’d rather get it right the first time, which is the whole reason we keep the parts conversation open and honest before we ever pick up a wrench.

Which FAAC Models This Applies To

FAAC has been making gate operators and hardware for decades, and the hinge and roller setups vary a bit across their lines. The most common units we see in Arlington driveways are the swing gate operators paired with FAAC’s own post hinges and the slide gate models running on FAAC track rollers. Older FAAC 400 series and 415 models, the 540 and 550 series, and the newer 844 automation packages all use specific roller diameters and hinge pin offsets that aren’t universal.

To identify the right part, we start with the model number stamped on the operator housing or on the underside of the gate frame, then measure the hinge pin diameter and the roller groove. A FAAC slide gate roller, for instance, typically rides a track with a specific width and the roller itself sits on a sealed bearing – not a bushing, which is where cheaper aftermarket versions fail first in Arlington’s fine clay dust. Aftermarket rollers can work fine on lighter gates, but for the heavier ornamental iron you see in neighborhoods like Viridian or older streets off Park Row, we lean toward OEM-spec FAAC parts or a machined equivalent we’ve tested. The risk with bargain rollers isn’t that they look wrong – it’s that they wear out twice as fast and take the track with them.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• The gate sags toward the latch side. That sag is almost never a bent panel – it’s a worn hinge pin or an egged-out hinge bore at the post. The longer it runs that way, the more the post itself starts to lean, and that’s a much bigger repair.
• You hear a grinding or shrieking when the gate moves. Dry or collapsed roller bearings make that sound, and in Arlington’s summer dust, dry bearings don’t stay dry long. Lubing them might buy a couple weeks, but a shrieking roller is already shot.
• The gate jerks or stutters mid-travel. A flat-spotted roller or a hinge that’s binding makes the gate hesitate in the same spot every time. The motor responds by pulsing, which shortens its life.
• You can rock the gate side to side by hand. Play at the hinge means the pin or bushing is worn beyond tolerance. A FAAC gate should swing without lateral wobble when the hinge is right.
• The gate scrapes the driveway or drags a track mark. That’s roller failure or a hinge that has dropped enough to change the gate’s sweep. Left alone, it chews up track, bearing plates, and eventually the gate frame itself.

Replacement Cost & What’s Included

For FAAC hinge and roller replacement in Arlington, installed pricing typically falls between $140 and $320. A single slide gate roller swap on a light residential gate starts at the lower end. Bigger jobs – a pair of swing gate hinges with new pins and bushings, or a full roller set on a heavy slide gate – land near the top. If the hinge post itself needs welding or shimming, that’s priced separately and we’ll tell you before we ever strike an arc.

Every quote includes the parts, labor, and clean-up, and the price we agree on is the price you pay. We don’t load the invoice after the fact. The work carries our 90-Day Done Right Promise in writing, and if something feels off after we leave, one call brings us back. No trip charge inside the county, and we’ll quote the whole thing over the phone if you can describe what you’re hearing or show us a photo.

DIY or Call Us?

What you can do safely is look: check for visible rust at the hinges, watch whether the rollers are turning or just sliding, and listen for a change in the gate’s normal sound. What you shouldn’t do is unbolt a swinging gate or a tensioned slide gate on your own. Even a “light” steel gate has real weight, and when the last hinge bolt comes out, that weight has to go somewhere. We’ve seen garage floors cracked and fence posts ripped out by a gate that got away.

FAAC gates in particular ride on tight tolerances, and a hinge that’s even slightly out of line will burn up the operator – a $175 hinge job becomes a $900 motor replacement. If you’re in Arlington and the gate is acting up, call (817) 241-4067 and describe what it’s doing. We’ll give you a straight answer, and if we need to come look, the trip charge inside the county is zero.

FAQs