Ghost Controls Gate Parts & Welding Nationwide | Gatewood Fence & Gate

Ghost Controls Gate Parts & Welding in Arlington: What to Know First

We repair and replace parts on Ghost Controls gate openers across Arlington, including hinge replacements, post replacement, rail repair, custom welding, rollers, and latch work. Most parts jobs are quoted and completed within a few days, and every repair starts with a free estimate before any work begins. If your Ghost Controls gate won’t open, sags, or makes a noise it didn’t make last month, call (817) 241-4067 and a live person picks up. This page is for Arlington homeowners with a Ghost Controls opener on a driveway gate, farm gate, or side gate who want the hardware fixed right, not swapped for something they don’t need.

Call (817) 241-4067

How Ghost Controls Products Fail - and How We Fix Them

Gatewood Fence & Gate is an independent Ghost Controls service provider, which means we’re not tied to a corporate repair script, and we don’t get paid to sell you a new opener. We fix what’s broken. Here’s what we find on Ghost Controls gates in Arlington:

• Arm bracket welds cracking on the gate leaf. On Ghost Controls swing arm kits such as the AXDP and AXD series, the bracket that connects the actuator arm to the gate often carries more load than the installer planned for. Arlington clay soil shifts with the seasons, the post moves a fraction of an inch, and suddenly that arm bracket is fighting the gate instead of pushing it. The crack starts at the weld toe and spreads. We cut out the cracked bracket, weld in a properly gusseted mount, and the problem stays gone.
• Hinge posts loosening and allowing the gate to drag. Ghost Controls openers will happily cycle a gate that has sagged enough to scrape the ground, and the opener pays the price in stripped gears. The arm pushes harder to move the same gate, heat builds in the actuator, and failure follows. We pull the hinge post, set it in concrete with proper depth for Arlington’s freeze-thaw cycle, and re-hang the gate so the opener works with the gate instead of against it.
• Actuator arm rod end wear on the VELOX and AXD series. The rod end at the gate bracket is a wear part on Ghost Controls linear actuators, and when it develops slop, the gate shudders at the start and stop of every cycle. A shuddering gate wears out the opener gearbox faster than anything else we see. Replacing the rod end is a simple parts job, but skipping it is how Ghost Controls openers end up dead in two years.
• Rail and roller damage on slide gate conversions. Homeowners sometimes convert a Ghost Controls swing opener to push a slide gate using aftermarket hardware. The slide rail gets welded low to dodge a fence line, a roller binds, and the opener stalls mid-travel. We see it in the older Arlington neighborhoods where fences run tight to the property line. We re-level the rail, replace the rollers with units rated for the gate weight, and the opener stops tripping its force limit.
• Latch and lock hardware fighting the opener’s force settings. A Ghost Controls opener set to auto-close will push against a magnetic lock or latch that’s misaligned, trip its obstruction sensor, and reverse. The owner thinks the opener is broken. We align the latch so it closes without strain, adjust the force limits properly, and the opener stops acting up. Nine times out of ten, the “bad opener” is a latch that a previous installer mounted half an inch off.

Our Ghost Controls Gate Parts & Welding Process

Here’s what happens when you call us about a Ghost Controls gate in Arlington:

1. 1
   You call (817) 241-4067. A live person answers, 24/7. We ask what the gate is doing, what the opener model is if you know it, and when you’re available for someone to come look.
2. 2
   We come see the gate. No trip charge inside the county. We watch the full cycle, inspect the hinges, roller, brackets, and welds, and we tell you what’s actually wrong, not what we’d like to sell.
3. 3
   Parts decision: OEM vs aftermarket. If the part is within the Ghost Controls warranty or it’s something where OEM tolerances matter, we get the OEM part. If a quality aftermarket part does the job better for less, we tell you that too, and we tell you why. You make the call with real information.
4. 4
   We fabricate and weld on site. Your gate stays in your driveway. We don’t haul it off, because a gate fixed in place is a gate you saw get fixed. No mystery work in some other shop.
5. 5
   Cycle testing and adjustment. We run the opener through its full travel 15 to 20 times, adjust the force limits and travel stops, and check the safety sensors with an actual obstruction test.
6. 6
   The 90-Day Done Right Promise goes in writing. If something we fixed isn’t done right, one call brings Hal back. No runaround, no service ticket maze.

What Ghost Controls Gate Parts & Welding Costs in Arlington

Every job is different, so here’s what we actually see on Ghost Controls work in Arlington, not a national average that means nothing:

• Hinge replacement (one or two hinges, welded on site): $180-$420 depending on gate weight and access.
• Post replacement (hinge post pulled, re-set in concrete, gate re-hung): $350-$700 depending on post size and concrete condition.
• Rail repair on a slide gate: $220-$500 for re-level, welding, and roller replacement.
• Custom welding (bracket repair, frame crack, gusset work): $120-$350 for typical Ghost Controls arm bracket or gate frame repair.
• Gate rollers replaced (set of two): $150-$300 for rollers rated to the gate weight, including alignment.
• Latch and lock realignment or replacement: $90-$250 for standard latches and magnetic locks.

What moves the price: gate weight, post condition, access for the welding rig, and whether the previous installer left something we have to un-do before we can fix the real problem. Whatever the number, you get it in writing and you approve it before any work starts. Call (817) 241-4067 for a free estimate.

Why Arlington Homeowners Call Gatewood Fence & Gate for Ghost Controls Work

Hal Gatewood has been fixing gates around Arlington since 2001, back when he was still driving a truck with a busted AC and figuring things out one broken hinge at a time. The name is on the shop, and the shop is down the road. If we weld a bracket on your Ghost Controls gate and it fails three months later, you don’t call a call center three states away. You call us, and we come back, because the 90-Day Done Right Promise is in writing on every job. We’re also certified on eight other major brands including LiftMaster, Mighty Mule, and DoorKing, which means if your Ghost Controls opener is truly done for, we can tell you what actually makes sense as a replacement instead of guessing. And when you call at 10 p.m. because the gate won’t close, a live person answers. That’s not a perk. That’s the baseline.

FAQs