Linear Hinge & Roller Replacement Nationwide | Gatewood Fence & Gate

Linear Hinge & Roller Replacement: The Arlington Owner’s Guide

We stock and install Linear-compatible hinges and rollers for most residential gate models, with typical installed pricing in Arlington running $240 to $480 depending on how many hinges or rollers failed and what the gate weighs. Most jobs are same-day when we have the exact part on the truck, which we usually do for Linear’s common light- and medium-duty swing and slide gate lines. What owners usually notice first: the gate starts dragging on one corner, makes a grinding sound halfway through its travel, or the latch won’t line up like it did last year. By the time you hear it scraping, the hinge or roller has been wearing for months – it’s just finally loud enough to notice.

Call (817) 241-4067

Key Takeaways

• Linear hinge and roller failures are almost always repairable without replacing the whole gate or operator.
• We carry common Linear-compatible hinge pins, rollers, and brackets on the truck for same-day replacement in Arlington.
• Upfront pricing, quoted and agreed before any work starts. No surprise invoices.
• Every replacement carries the 90-Day Done Right Promise in writing.

Which Linear Models This Applies To

Linear has been making gate operators and hardware for decades, and their parts show up on a lot of Arlington driveway gates installed between roughly 1998 and today. The hinge and roller hardware varies by gate type: swing gates use barrel hinges, weld-on or bolt-on, while slide gates ride on steel rollers in a track or on cantilever roller assemblies. The compatibility gotcha we see regularly on Arlington service calls is that Linear’s lighter residential swing gate hardware from the older UV series and the newer ASO/ASR line does not interchange cleanly with the heavier commercial H series without drilling or re-welding mounting holes. The bolt spacing is different, and a homeowner who orders a hinge based on a photo will often get a part that’s close but not right.

Before you order anything, check the mounting plate or bracket for a stamped number. If it’s gone, measure the bolt hole spacing center to center and the pin diameter. That gives us enough to match it. We recommend OEM Linear parts when the gate is still under any kind of operator warranty, because aftermarket components can technically void the hardware warranty if a later claim comes up. Outside of warranty, a quality aftermarket equivalent with a sealed bearing and a stainless pin will often outlast the original in Texas weather. We carry both options and will tell you honestly which one makes sense for your gate.

Signs Your Linear Hinge & Roller Replacement Is Failing

• The gate drags on the ground or scrapes at the latch post. This means a hinge pin or roller bearing has worn enough that the gate is sitting lower than it was installed. The operator is now pushing against the ground, which shortens its life fast.
• A grinding or squealing sound when the gate moves. Sealed bearings in Linear rollers eventually lose their grease in Arlington heat, then run dry. Once you hear metal on metal, the bearing is done – oiling it buys a week, not a season.
• The gate wobbles side to side as it travels. That’s play in the hinge barrel or a flat spot on a roller. If left alone, the wobble wallows out the mounting holes and turns a $60 roller job into a bracket rebuild.
• Rust staining running down from the hinge or roller bracket. Water gets into the bearing or pin, and what runs out is rust. This is the silent killer on Arlington gates that face north and never fully dry out after a rain.
• The operator trips its force setting and reverses. When the gate binds on a bad roller or hinge, the Linear control board reads the extra resistance and backs off. The board thinks it’s saving a child; really it’s a hinge telling you it’s done.

We see the same pattern on Arlington gates over and over: a roll pin shears, the gate sags a half inch, and then every other component starts working harder to compensate. One worn roller will take out the next one down the line.

Replacement Cost & What’s Included

Here’s what Linear hinge and roller replacement typically runs in Arlington:

• Single barrel hinge replacement (weld-on or bolt-on): $85-$150 installed
• Single roller and bearing assembly (slide gate): $95-$175 installed
• Full hinge set on a light residential swing gate (2 hinges): $220-$380 installed
• Complete roller set on a slide gate (2-4 rollers): $260-$480 installed
• Cantilever roller assembly replacement: $300-$550 installed

What moves the price: gate weight, whether the hinge is welded or bolted, how much adjustment the gate needs after the part goes in, and how stubborn the old hardware is to remove. Every quote is given upfront, before we turn a wrench, and the number we agree on is the number on the invoice. The price is quoted and agreed before any work starts. All hinge and roller replacements carry the 90-Day Done Right Promise: if it’s not done right, we make it right. No trip charge inside the county, and you’re welcome to a free second opinion on any written estimate you’ve gotten from someone else.

DIY or Call Us?

Here’s the honest split. You can safely clean the track, check for obvious obstruction, and take a clear video of the noise so you can describe it to whoever you call. You can also inspect for wobble by grabbing the gate mid-span and giving it a firm shake to see where the play is. What you should not do yourself is pull a gate off its hinges or neutralize a slide gate roller while the gate is still under tension or weight-bearing – a heavy gate that slips off a jack or jackstand can do serious damage to you or a kid standing nearby. That’s not a scare tactic, it’s just physics. We’ve also seen enough stripped bolts and cross-threaded pins to tell you straight: the hardware is not where the DIY savings usually live. If you’re in Arlington and the gate is dragging or grinding, call (817) 241-4067 and we’ll put eyes on it the same day. If you’re handy, we’ll tell you exactly what you’re looking at so you can decide with a clear head.

FAQs